View H431CA_411549.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

HI-SINCERITY
MICROELECTRONICS CORP.
Spec. No. : HA200216 Issued Date : 1998.04.08 Revised Date : 2002.08.27 Page No. : 1/4
H431AA/BA/CA
AJDUSTABLE SHUNT REGULATOR
Description
The H431 series are three-terminal adjustable regulators with guaranteed thermal stability over applicable temperature ranges. The output voltage may be set to any value between VREF (approximately TO-92 2.495 volts) and 36 volts with two external resistors. These devices have a typical dynamic output impedance of 0.2. Active output circuitry provides a very sharp turn-on characteristic, making these devices excellent replacement for zener diodes in many applications.
Features
* Programmable output voltage * Temperature coefficient is 50ppm/C typical * Temperature compensated for operation over * full temperature range * Low output noise voltage * Fast turn on response
Classification
Rank VREF A 2.4952% B 2.4951% C 2.4950.5%
Absolute Maximum Ratings
(Operating temperature range applies unless otherwise specified) Characteristics Cathode Voltage Cathode Current Range (Continuous) Reference Input Current Range Power Dissipation Operating Temperature Range Storage Temperature Range Symbol VKA IK IREF PD Topr Tstg Value 37 -100~+150 0.05~+10 770 0~+70 -65~+150 Unit V mA mA mW C C
H431AA, H431BA, H431CA
HSMC Product Specification
HI-SINCERITY
MICROELECTRONICS CORP.
Functional Block Diagram & Symbol
Functional Block Diagram :
Cathode Reference VREF + Anode
Spec. No. : HA200216 Issued Date : 1998.04.08 Revised Date : 2002.08.27 Page No. : 2/4
Symbol :
Cathode
Reference
Anode
Test Circuits
IN IREF IZ VREF R2 VREF II VZ IN R1 II VZ IN VZ
IREF IZ
Fig1. Test Circuit for VZ=VREF
Fig 2. Test Circuit for VZ>VREF Note : VZ=VREF(1+R1/R2)+IREFxR1
Fig3. Test Circuit for Off-State Current
Electrical Characteristics ( Ta=25C unless otherwise specified )
Characteristics Symbol Test Conditions Reference Input Voltage H431AA VREF VKA=VREF, IK=10mA H431BA H431CA V =V , I =10mA Deviation of Reference Input Voltage VREF(dev) KA REF K Over-Temperature TminTaTmax IK=10mA, Ratio of Change in Reference Input VREF / VKA=10V-VREF Voltage to the Change in Cathode VKA IK=10mA, Voltage KKA=36V-10V IK=10mA, R1=10k, Reference Input Current IREF R2= Deviation of Reference Input Current I =10mA, R1=10k, IREF(dev) K Over Full Temperature Range R2=, Ta=Full Range Minimum Cathode Current for IK(min) VKA=VREF Regulation Off-State Cathode Current IK(off) VKA=36V, VREF=0 VKA=VREF, f1.0KHz Dynamic impedance ZKA IK=1 to 100mA Min Typ Max Unit 2.445 2.495 2.545 2.470 2.495 2.520 V 2.480 2.495 2.510 4 -1.4 -1.0 2 0.4 0.4 0.1 0.2 17 -2.7 -2.0 4 1.2 1.0 1.0 0.5 mV mV V uA uA mA uA
H431AA, H431BA, H431CA
HSMC Product Specification
HI-SINCERITY
MICROELECTRONICS CORP.
Characteristics Curve
Cathode Current & Cathode Voltage
150 125
0
Spec. No. : HA200216 Issued Date : 1998.04.08 Revised Date : 2002.08.27 Page No. : 3/4
Change in Reference Input Voltage & Cathode Voltage
-5 -10 -15 -20 -25 -30 -35 -40 IK=10m TA=25C
75 50 25 0 -25 -50 -75 VKA=Vref TA=25C -3 -2 -1 0 1 2 3 4
-100
Change in Reference Input Voltage (mV)
100
Cathode Current (mA)
0
10
20
30
40
50
Cathode Voltage (V)
Cathode Voltage (V)
Dynamic Impedance & Frequence
100
Cathode Current & Cathode Voltage
1000 800 600 400 200 0 VKA=Vref TA=25C -200 -400
Impedance (ohm)
10
1
IK=10mA to 100mA TA=25C 0.1 1 10 100 1000 10000
Cathode Current (uA)
-2
-1
0
1
2
3
Frequency (Hz)
Cathode Voltage (V)
Noise Voltage & Frequency
100 100
Small Signal Voltage Amplification & Frequency
Noise Voltage (nV/Hz )
1/2
10
Voltage Amplification (dB)
VKA=Vref IK=10mA TA=25C
10
IK=10mA TA=25C 1 1000
1 10 100 1000 10000 100000
10000
100000
1000000
10000000
Frequency (Hz)
Frequency (Hz)
H431AA, H431BA, H431CA
HSMC Product Specification
HI-SINCERITY
MICROELECTRONICS CORP.
TO-92 Dimension
A B
1 2 3
Date Code
Spec. No. : HA200216 Issued Date : 1998.04.08 Revised Date : 2002.08.27 Page No. : 4/4
2
Marking:
H 431 A
Control Code
3
C
Style: Pin 1.Reference 2.Anode 3.Cathode
D
H I E F
G
1
3-Lead TO-92 Plastic Package HSMC Package Code: A
*: Typical
DIM A B C D E F
Inches Min. Max. 0.1704 0.1902 0.1704 0.1902 0.5000 0.0142 0.0220 *0.0500 0.1323 0.1480
Millimeters Min. Max. 4.33 4.83 4.33 4.83 12.70 0.36 0.56 *1.27 3.36 3.76
DIM G H I 1 2 3
Inches Min. Max. 0.0142 0.0220 *0.1000 *0.0500 *5 *2 *2
Millimeters Min. Max. 0.36 0.56 *2.54 *1.27 *5 *2 *2
Notes: 1.Dimension and tolerance based on our Spec. dated Apr. 25,1996.
2.Controlling dimension: millimeters. 3.Maximum lead thickness includes lead finish thickness, and minimum lead thickness is the minimum thickness of base material. 4.If there is any question with packing specification or packing method, please contact your local HSMC sales office.
Material:
* Lead: 42 Alloy; solder plating * Mold Compound: Epoxy resin family, flammability solid burning class: UL94V-0
Important Notice:
* All rights are reserved. Reproduction in whole or in part is prohibited without the prior written approval of HSMC. * HSMC reserves the right to make changes to its products without notice. * HSMC semiconductor products are not warranted to be suitable for use in Life-Support Applications, or systems. * HSMC assumes no liability for any consequence of customer product design, infringement of patents, or application assistance.
Head Office And Factory:
* Head Office (Hi-Sincerity Microelectronics Corp.) : 10F.,No. 61, Sec. 2, Chung-Shan N. Rd. Taipei Taiwan R.O.C. Tel: 886-2-25212056 Fax: 886-2-25632712, 25368454 * Factory 1: No. 38, Kuang Fu S. Rd., Fu-Kou Hsin-Chu Industrial Park Hsin-Chu Taiwan. R.O.C Tel: 886-3-5983621~5 Fax: 886-3-5982931
H431AA, H431BA, H431CA
HSMC Product Specification

▲Up To Search▲

Price & Availability of H431CA

	To Download H431CA Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .